PLC & Control Systems

Choosing Industrial Communication Systems for Factory Automation

Publication Date

Nov 07, 2026

author

Victor Lin (Chief Software Architect)

The best industrial communication systems for factory automation are not necessarily those with the highest advertised data rates. The right choice is the one that delivers the required data to the right devices within a predictable time, continues operating under defined fault conditions, and fits the equipment already on the factory floor.

Start with the application, not the protocol name. A motion-control network connecting synchronized drives has different requirements from a connection that sends production counts to a dashboard. Treating both as ordinary Ethernet traffic can produce a design that looks compatible on paper but fails when timing, recovery, or maintenance becomes critical.

Define the data paths before comparing protocols

Map the devices that need to exchange information and describe what each exchange must accomplish. A useful starting point is to separate traffic into three groups:

  • Control traffic: Cyclic I/O, drive commands, position feedback, and other data used directly by machines to control a process.
  • Supervisory traffic: Operator commands, alarms, recipes, and production status exchanged between controllers, interfaces, and supervisory systems.
  • Information traffic: Historical data, condition-monitoring measurements, and reporting data sent to servers or edge applications.

These categories can share infrastructure in some designs, but they do not have the same tolerance for delay or interruption. A delayed temperature trend may have little immediate impact; a delayed command or feedback signal may affect machine performance or trigger a stop.

For each data path, record the source and destination, update interval, acceptable delay, consequences of missed messages, and required behavior during a communication loss. Include expected device counts and traffic growth. This inventory provides a basis for comparing systems against actual requirements instead of a generic feature list.

Choosing Industrial Communication Systems for Factory Automation

Evaluate timing as an end-to-end requirement

Data rate describes how quickly bits can travel over a link. It does not, by itself, tell you when a sensor value will be available to a controller or when a drive will act on a command. For control applications, the more useful questions concern latency, jitter, update time, and synchronization.

Latency is the time a message takes to travel through a defined path. Jitter describes variation in timing. A system with a low average delay can still be unsuitable if occasional delays exceed what the process can tolerate. Determinism means communication behavior is sufficiently predictable for the application; it does not mean that all devices and network configurations have identical performance.

Consider the complete path: sensor acquisition, device processing, network transmission, controller task scheduling, output processing, and actuator response. A network update interval is only one part of that chain. If a controller reads inputs or executes its control task less frequently than expected, a fast network alone will not deliver the intended response.

Synchronized motion adds another requirement: devices may need a shared sense of time, not just frequent messages. Check whether the chosen controller, drives, switches, and network configuration support the synchronization functions required by the motion application. For noncritical monitoring, the cost and complexity of those functions may be unnecessary.

Compare communication options in their intended roles

Option Where it often fits Selection constraint
Industrial Ethernet protocols Controller-to-I/O communication, drives, machine integration, and applications that need relatively fast or predictable exchange Timing, synchronization, topology, and diagnostic capabilities depend on the protocol and the specific devices and network design.
Fieldbus networks Existing installations and distributed devices where established equipment compatibility or simpler wiring is valuable Bandwidth, network size, diagnostics, and integration options vary; legacy support and spare parts deserve attention.
OPC UA Structured information exchange between machines, supervisory systems, and enterprise or edge applications Interoperability depends on supported profiles, information models, and configuration; ordinary deployments should not be assumed to meet motion-control timing.
MQTT Publishing telemetry and events to applications through a broker Delivery behavior depends on configuration and connectivity; it is generally not a substitute for a deterministic machine-control network.
Wireless networks Mobile equipment, rotating assets, temporary installations, and locations where cabling is impractical Coverage, interference, roaming, security, and application tolerance for interrupted communication must be evaluated on site.

These options can coexist. A machine may use an industrial Ethernet protocol for control, an information interface for production data, and wireless connectivity for a mobile asset. The design question is where each boundary belongs and what happens when data crosses it.

Do not assume two devices can exchange all required functions simply because both list Ethernet or the same protocol family. Confirm the specific communication roles, supported device profiles, software versions, and features needed for the application. A device that can publish basic data may not expose the diagnostics, configuration parameters, or synchronized operation needed for the intended design.

Topology and recovery can determine production impact

A line, star, ring, or combination of topologies can all be appropriate, depending on the physical layout and availability requirement. A line can simplify cabling along a machine, but a break may affect devices beyond the fault. A star provides separate paths to a central switch, while making that switch and its power supply important dependencies. Ring designs can provide an alternative path when supported and configured correctly, but recovery behavior depends on the actual devices and redundancy mechanism.

Ask what the machine must do during a cable break, switch failure, controller restart, or loss of power to a device. “Redundant” is not a complete requirement. Define which failures are covered, whether traffic is interrupted, how long recovery may take, and whether the process can tolerate that interruption.

Redundancy also needs independent failure paths. Two cables routed through the same exposed conduit can fail together. Similarly, redundant switches connected to the same unprotected power source may not address the failure that matters. Draw the physical paths alongside the logical network diagram before deciding that a design has adequate resilience.

Check integration beyond the protocol label

Existing controllers, drives, remote I/O, safety devices, and maintenance tools often narrow the practical choices. Build an integration matrix listing each device, its required functions, communication role, firmware, configuration tool, and diagnostic access. Include planned replacements, not just installed equipment.

Gateways can connect otherwise incompatible systems, but they introduce another point to configure, support, and potentially fail. Examine how the gateway maps data, handles lost connections, reports stale values, and recovers after restart. A translated value that remains visible after the source has stopped updating can be more misleading than a clear communication fault.

Also consider ownership of device configuration. If replacing an I/O module requires proprietary software, a specialist laptop, or manual parameter entry, that affects recovery time. Look for an approach that allows authorized maintenance staff to identify faults and restore a replacement using documented procedures.

Separate functional safety from ordinary network reliability

A reliable control network is not automatically a safety-related communication system. Where communication carries safety functions, the complete safety architecture must be designed and validated for the application, including compatible safety controllers, devices, configuration, and the behavior required when communication fails.

Confirm how the safety function responds to lost, delayed, repeated, or corrupted messages and how a restart is authorized. Standard control commands and safety functions may use related infrastructure in some designs, but their requirements and validation are not interchangeable.

Include cybersecurity and maintainability in the selection

A network that is easy to connect can also be easy to expose unintentionally. Define which devices and users need access, separate control traffic from less-trusted networks where appropriate, and restrict remote maintenance paths. Review authentication, access control, logging, backup, and update capabilities across controllers, switches, gateways, and supporting software.

Security measures must fit operational constraints. For example, an update may require a production stop or change the behavior of a device interface. The evaluation should cover how updates are tested, approved, installed, and rolled back, as well as how configurations are restored after equipment replacement.

Diagnostics are equally important. A useful system should help technicians distinguish a failed device from a damaged cable, an overloaded link, or a configuration mismatch. Review the visibility available from the controller and network tools, including port status, fault history, device identification, and indications that communication data has become stale.

Test the proposed system under representative conditions

A specification sheet is a starting point, not an acceptance test. Assemble a representative configuration with the intended controllers, devices, switches, cable types, software versions, and traffic. Where a full production setup is impractical, make the limits of the test configuration explicit and target the highest-risk interactions.

Agree on pass criteria before testing. The following checks expose issues that a protocol comparison alone may miss:

  1. Timing under load: Measure the relevant end-to-end response and variation while control and expected background traffic are present. Include the controller task and device processing, not just network transmission.
  2. Fault response: Disconnect links, restart devices, and interrupt power at defined points. Record alarms, machine behavior, recovery time, and any manual intervention needed.
  3. Interoperability: Exercise the required device functions, diagnostics, parameter changes, and restart sequences across the proposed equipment versions.
  4. Physical conditions: Assess cable routing, connectors, grounding, electromagnetic interference, temperature, vibration, and exposure to liquids or cleaning processes where relevant.
  5. Maintenance: Replace a representative device or restore its configuration using the tools and permissions that the plant will actually have.

For wireless links, add coverage and roaming tests in the intended operating area, with machinery and other radio systems operating as expected. A successful stationary connection does not establish that a moving vehicle will maintain the same communication behavior throughout its route.

Make the decision with explicit trade-offs

Eliminate options that cannot meet mandatory control, safety, environmental, or integration requirements. Among the remaining candidates, compare the full installed and supported system: devices, switches, cabling, engineering tools, licensing where applicable, training, spares, and the effort required to diagnose and recover from faults.

The preferred system may not be the most feature-rich. A machine with demanding coordinated motion may justify specialized timing and synchronization, while a monitoring application may be better served by a simpler architecture. Document the assumptions behind the choice, the tested configuration, the failure cases covered, and the conditions that would trigger a design review as the factory expands.

Recommended News